Operation Manual Pega357
C T) TABLE OF CONTENTS (Continued) SECTION IV Additional Features PAGE CONTROL CAPABILITIES. Pega 357 with 04PC Control Layout Drawings ©Amada America, Inc. Print Date Revision 4.0 This document available on the World Wide Web at http://www.amada.
7 6 5 2 0 WSBK WTCG LBKUB TSTB WOPS WBDT WITT LBKUA.Single Mode Button ‘Tool Change Button Auto-index Brake (B) Upper L S.Optional stop ON/OF F Button.Optional Block Skip ON/OFF Button.Turret ON/OFF Button Auto-Index Brake (A) Upper LS WINCH LEPCB WCYC WMLK WSTM LCPUA LIPC. Press select Switch (Inching) External Program Number Search. Press Select Switch (Cycle) ‘Program Check Button ‘Stripping Miss ' ON/OFF Button Auto-Index Auto-Index Clamp (A) Position Upper LS Check 00 p LWHDR j LCPUB LBKDB. 0051 WEDT W M E M 1 WTA P WMDI WMAN ‘Edit Mode ‘Memory Mode ‘Tape Mode.MDI Mode ‘Manual Mode 0052 TD9 TOT TD6 TD15 TD5 TD4 0053 WF1 WF2 WF3 I I W1,. Feedrate Switch IF1) ‘Feedrate Switch IF2).
Amada Pega 357 Maintenance Manual
Feedrate Switch IF3).Feedrate Switch (1) ‘Feedrate Switch 12) 0054 TD10 TD11 TD14 TO13 TD12 TD2 TD1 0055 LSPIA LSPIB LSPOA LSPQB LWPH LMDN Index Pin Index Pin Index Pin Index Pin Work Pusher WZ E R Retract Mode TD3 W2 Feedrate Switch 13) TDO (Upper) IN (Lower) IN (Upper) LS LS OUT LS (Lower) OUT LS Origin LS. Copyright © 1998 by Amada Engineering & Service Co., Inc. 14921 East Northam Street, La Mirada, CA 90638All rights reserved. No part of this book shall be repr. FOREWORDThis manual has been prepared to acquaint you with the installation, operation and maintenance procedures of your Amada machine. We urge that you read t.JSECTION 1 - ‘MACHINE DESCRIPTIONTABLE.CARRIAGE.CLAMPS.X-GAUGE BLOCK. SECTION 4 - OPERATIONPREPARATION.4-lAUTOMATIC OPERATIONTAPE mode.4-2MEMOR.
SECTION 1TABLE.CARRIAGE.CLAMPS.X-GAUGE BLOCKTURRET.WORK HOLDERSSTRIKER.INDEX PINS.WORK CHUTE. 'TOOL BALANCER.P. The Amada Turret Punch- Press is equipped with a Numerical Control (NC) system in which three driving axes are simultaneously controlled by three DC servo motor. The turret selects the desired tool quickly by automatically rotating in either direction for the shortest index time.
It is a triple track turret, and is drive. The work chute drops small workpieces or scrap down through the window 200 mm x 200 mm (7.8” x 7.8') cut into the table, The window is opened and closed by. A three-phase induction motor is used as the press motor. This motor drives the flywheel, which generates the force required to-punch the worksheet.The clutch a. CLUTCH AND BRAKE (PEGAKING ONLY)The clutch and the brake are the most important parts of the press.
The torque of the flywheel is instantly transmitted to the c. This machine is designed so that the clamps can actually enter between the upper and lower turrets. This feature minimizes the area in which punching cannot be. UNCLAMPING PROTECTIONDuring automatic operation, the clamps will not open even if the foot switch is accidentally pressed.
However, when either the PROGRAM STOP. PLACEMENT.AIR SUPPLY.ELECTRICAL POWER CONNECTION2-12-22-2. When your machine is delivered, an AMADA service engineer will be sent to your facility. Installation of the machine should be accomplished in accordance with h.
Operation Manual 357 Magnum
It is necessary to supply clean, dry air to this machine. When in use, it requires 80 Q (2.8 ft3) of air per minute. The line pressure must be more than 5.0 kg/. NC UNIT CONTROL PANEL.CONTROL PANEL A.CONTROL PaNEL 8.ELECTRICAL ENCLOSURE. 1.NC POWER ON BUTTONPush this button to turn the NC unit on. The circuit breaker (84) must be on before pushing this button.2:’ NC POWER OFF BUTTONvPush this&.
5. CURSOR BUTTONSThese buttons control the position of the cursor on the CRT. When the t button is pushed, the cursor will move upward; when th.J button is. 14. ORIGIN BUTTON14. ORIGIN BUTTONAThis button resets the X- and Y-axis displayed coordinate values to their origins.15.
EDIT BUTTONSThese three buttons edit th. 17, NC READY LIGHT (green)This light comes on when the NC system, including the servo unit, is ready for operation. The light will go out if either of the follo. 22. C-ORIGIN- LIGHT (Option) (green)This light comes on when the C-axis (option) has been returned to its origin in the RETRACT mode.
It will go out if the NC R. 30. AIR DOWN LIGHT (red)This light comes on if air pressure to the machine drops below approximately 3.0 kg/cm2 (43 psi). The machine will go to an emergency st. 37. STRIPPING MISS LIGHT (red)This light comes on and the machine stops if a punch does not retract properly.
After the cause of the problem has been eliminated. 43.
MODE SWITCHThis switch selects any of the following operational modes.EDIT mode — Used for the following:(a) To enter tape programs into memory.(b) To edi. 47. STOP BUTTON (w/red light)When this button is pushed, its light will come on and the machine will stop. This button has the same function as STOP buttons (66. 53. STRIPPING MISS ON/OFF BUTTON (w/light)When this button light is on, the stripping miss detector will stop the machine if a punch fails to retract properly.
This switch selects press operational modes. It can be locked in any mode by removing the key.JMODE switch I PRESSSELECT position switch positionPress operation. When the OVERRIDE light (27) comes on, pushing this button will resume machine operation.
This button has the same function as button (83) on control panel B.CA. CONTROL PANEL BTURRET ONThis button stops the machine. Reset the button by turning it clockwise, This button has the same function as STOP buttons (47) and (66). 77.
STRIKER SWITCHThis switch is effective only in the MANUAL mode. It sets the striker above one of the triple turret tracks. During automatic operation, this. 11rFAN MOTOR SWITCHPRESS MOTOR REPOSITIONING HYDRAULIC SWITCHDETECTOR MOTORSWITCH SWITCHAUTO-INDEXSWITCHAll electric power to the machine and NC unit goes throu. The tool balancer is standard equipment on the COMA series model as well as the VELA II equipped with thick turret and the PEGA KING.90.
PRESSURE 4-1/2' CONTROL. 93.
3-1/2' UP/DOWN SWITCHThis switch is used when removing or installing punches having a 3-1/2' diameter.To support the weight of the punch, proceed as follows. When the accumulator pressure drops below the specified level, this light comes on and the machine will come to an emergency stop.