• Delta Vfd B Manual

Huanyang Chinese VFD settings and manual here! Submitted by guest (not verified) on Wed,. You can see download the inverter manual from web link.

How to setup Chinese VFD to 2.2KW spindle. Picture included, as well as PDF manual. (I dont own the product, just figured this would help EVERYone else out that does!!) PDF file is 15.8MB (large).

It actually is very easy to read and navigate, i was impressed on how informational it is. Hope this helps someone! I drafed the wire picture.

Please see from the link: 2. You can see download the inverter manual from web link: 3. I just tell you how to set up VFD as following Firstly, adjust the PD013 to 8 (set the setting to factory setting) Secondly, adjust the PD005 to 400 Thirdly, adjust the PD004 to 400 Finally, adjust the PD003 to 400 Finally, adjust the PD144 to 3000 Note: you should set PD013, PD005, PD004,PD003, PD144 in order. It mean you should firstly set PD013, then PD005, then PD004, then set PD003, finally set PD144. Note: after you set the all above parameter, then please recheck the PD005, PD004, PD003 value is 400 or not to confirmed that you already set it. (note: please do not check the PD013, or all the setting will go to factory setting) The reason we let you recheck is that if you do not set it at 400, then when you run the spindle motor, the spindle motor will be over-current, then the spindle will very hot and then within 5 minutes, it will broken. How to setup Chinese VFD to 2.2KW spindle.

Picture included, as well as PDF manual. (I dont own the product, just figured this would help EVERYone else out that does!!) PDF file is 15.8MB (large). It actually is very easy to read and navigate, i was impressed on how informational it is.

Hope this helps someone! I drafed the wire picture.

Please see from the link: 2. You can see download the inverter manual from web link: 3. I just tell you how to set up VFD as following Firstly, adjust the PD013 to 8 (set the setting to factory setting) Secondly, adjust the PD005 to 400 Thirdly, adjust the PD004 to 400 Finally, adjust the PD003 to 400 Finally, adjust the PD144 to 3000 Note: you should set PD013, PD005, PD004,PD003, PD144 in order. It mean you should firstly set PD013, then PD005, then PD004, then set PD003, finally set PD144. Note: after you set the all above parameter, then please recheck the PD005, PD004, PD003 value is 400 or not to confirmed that you already set it.

(note: please do not check the PD013, or all the setting will go to factory setting) The reason we let you recheck is that if you do not set it at 400, then when you run the spindle motor, the spindle motor will be over-current, then the spindle will very hot and then within 5 minutes, it will broken. I got this VFD, it worked only for 45 days. I got my 1.5 water cooled + VFD about a month ago for 250 bucks.including shipping. I could not be happier.

Took me a bit to get the VFD set up, but with all the threads here dealing with them it was easy to find the right settings. This thing out performs the trim routers I have had on my 24x24 by miles. I have gone threw 2 routers and countless bits due to lack of control over spindle speeds in the last year.

I am just a 'Home Hobbyist', and do a little custom work on the side. So my CnC is lucky if it runs 20 hours a week.

And if this lasts a year for me, it will more than paid for itself. Ken The spindle seems solid, and the VFD seems to be a vast improvement over 'older' models. Thank you for the information about setting things in the right order. I have one of these Huanyang 2.2KW VFDs as well and so far it's not working. Fruity loops 10 torrent. Not sure if its me or maybe a bad drive(?) I connected to a single phase 220VAC (which measures 245V). When applying power, after a few seconds I get 'LV' displayed. The manual indicated this is 'low voltage' and that I should check the input voltage, change in load, or missing phase.

After messing around with this myself and then resetting to defaults, I set the parameters as described above but no change. Has anyone seen this behavior or know what I need to do? You didnt describe your setup, but make sure you are using the 3 terminals listed as VR(+10V), VI (0-10V input), and ACM (analog common ground) Im not sure which legs of the pot go to which terminals, but you should use a volt meter and make sure that you are getting 0-10 volts on the VI terminal through the full range of your pot. If you setup is only giving you 0-5 volts then you can change pd071 to 1. Also to verify your other settings, you can get full speed control through the panel right?

Hi guys, Can you bring me some help on the configuration of this VFD?? Im trying to make a 3hp Pump to work this is to a WRO machine, specs on the pump are: 3.00 HP VAC 230 MAX S.F AMPS 11.6 cos p 0.75 rpm 3460 Works fine with the lower pressure but when i try to make it work to get a decent production the AMP on the VFD's panel goes till 14 and cuts down after that. Maybe im doing a wrong configuration or Do i just need another ( bigger ) VFD?? Thanks for your help BTW: i got the 3HP 2.2 KW model.

However this may also be caused by wrong parameters - make sure base frequency (Parameter 4) meets motor nominal frequency and stay within a reasonable frequency range. Christian Yo Christian, thanks for your quick answer, so can you please help me with this conf-?? I have read the whole manual and still i think im doing it ok.

Which are the parameters on the VFD that i should check? Thanks in advance Edit 1. Yes it looks like the freq. On the parameter 4 its on 50 HZ, but it cannot be changed to a higher one. Now taking a better inspection Pd003 (according the manual MAIN FREQUENCY) remains on 50Hz, cannot be changed to a higher freq im assuming that this is the input frequency., Pd004 now i set it on 60Hz but i read somewhere that is better to put a higher value (400 was the recommended frequency).

Is this safe for the VFD? Now Pd005 must be 60Hz or should i also changed it to 400 Hz? I have just setup a DigiSpeed alongside a 1.5Kw Huanyang Inverter. All the settings and configurations I have followed as per the information I have read on this forum. I have my terminals 3 terminals setup as VR(+10V), VI (0-10V input), and ACM (analog common ground). When I turn on the spindle with Mach3 I get corresponding voltage between VI and ACM which changes with selected speed all the way up to 9.8volts at full. I have set PD070 at 0 and tried 4 I have set PD001 and PD002 to external settings.

The spindle runs fine once I set it to operator but will not move or do anything if I try to command it from Mach3 Any ideas? I have spent some time on this without success!!! Regards Boyd NZ.

Add new comment.

How to setup Chinese VFD to 2.2KW spindle. Picture included, as well as PDF manual. (I dont own the product, just figured this would help EVERYone else out that does!!) PDF file is 15.8MB (large). It actually is very easy to read and navigate, i was impressed on how informational it is. Hope this helps someone! I drafed the wire picture. Please see from the link: 2.

You can see download the inverter manual from web link: 3. I just tell you how to set up VFD as following Firstly, adjust the PD013 to 8 (set the setting to factory setting) Secondly, adjust the PD005 to 400 Thirdly, adjust the PD004 to 400 Finally, adjust the PD003 to 400 Finally, adjust the PD144 to 3000 Note: you should set PD013, PD005, PD004,PD003, PD144 in order. It mean you should firstly set PD013, then PD005, then PD004, then set PD003, finally set PD144. Note: after you set the all above parameter, then please recheck the PD005, PD004, PD003 value is 400 or not to confirmed that you already set it. (note: please do not check the PD013, or all the setting will go to factory setting) The reason we let you recheck is that if you do not set it at 400, then when you run the spindle motor, the spindle motor will be over-current, then the spindle will very hot and then within 5 minutes, it will broken. How to setup Chinese VFD to 2.2KW spindle. Picture included, as well as PDF manual.

(I dont own the product, just figured this would help EVERYone else out that does!!) PDF file is 15.8MB (large). It actually is very easy to read and navigate, i was impressed on how informational it is. Hope this helps someone!

Delta Vfd B Manual

I drafed the wire picture. Please see from the link: 2. You can see download the inverter manual from web link: 3. I just tell you how to set up VFD as following Firstly, adjust the PD013 to 8 (set the setting to factory setting) Secondly, adjust the PD005 to 400 Thirdly, adjust the PD004 to 400 Finally, adjust the PD003 to 400 Finally, adjust the PD144 to 3000 Note: you should set PD013, PD005, PD004,PD003, PD144 in order. It mean you should firstly set PD013, then PD005, then PD004, then set PD003, finally set PD144. Note: after you set the all above parameter, then please recheck the PD005, PD004, PD003 value is 400 or not to confirmed that you already set it.

(note: please do not check the PD013, or all the setting will go to factory setting) The reason we let you recheck is that if you do not set it at 400, then when you run the spindle motor, the spindle motor will be over-current, then the spindle will very hot and then within 5 minutes, it will broken. I got this VFD, it worked only for 45 days. I got my 1.5 water cooled + VFD about a month ago for 250 bucks.including shipping. I could not be happier. Took me a bit to get the VFD set up, but with all the threads here dealing with them it was easy to find the right settings. This thing out performs the trim routers I have had on my 24x24 by miles. I have gone threw 2 routers and countless bits due to lack of control over spindle speeds in the last year.

I am just a 'Home Hobbyist', and do a little custom work on the side. So my CnC is lucky if it runs 20 hours a week. And if this lasts a year for me, it will more than paid for itself. Ken The spindle seems solid, and the VFD seems to be a vast improvement over 'older' models.

Thank you for the information about setting things in the right order. I have one of these Huanyang 2.2KW VFDs as well and so far it's not working. Not sure if its me or maybe a bad drive(?) I connected to a single phase 220VAC (which measures 245V). When applying power, after a few seconds I get 'LV' displayed. The manual indicated this is 'low voltage' and that I should check the input voltage, change in load, or missing phase. After messing around with this myself and then resetting to defaults, I set the parameters as described above but no change.

Has anyone seen this behavior or know what I need to do? You didnt describe your setup, but make sure you are using the 3 terminals listed as VR(+10V), VI (0-10V input), and ACM (analog common ground) Im not sure which legs of the pot go to which terminals, but you should use a volt meter and make sure that you are getting 0-10 volts on the VI terminal through the full range of your pot. If you setup is only giving you 0-5 volts then you can change pd071 to 1. Also to verify your other settings, you can get full speed control through the panel right? Hi guys, Can you bring me some help on the configuration of this VFD?? Im trying to make a 3hp Pump to work this is to a WRO machine, specs on the pump are: 3.00 HP VAC 230 MAX S.F AMPS 11.6 cos p 0.75 rpm 3460 Works fine with the lower pressure but when i try to make it work to get a decent production the AMP on the VFD's panel goes till 14 and cuts down after that.

Maybe im doing a wrong configuration or Do i just need another ( bigger ) VFD?? Thanks for your help BTW: i got the 3HP 2.2 KW model. However this may also be caused by wrong parameters - make sure base frequency (Parameter 4) meets motor nominal frequency and stay within a reasonable frequency range. Christian Yo Christian, thanks for your quick answer, so can you please help me with this conf-?? I have read the whole manual and still i think im doing it ok. Which are the parameters on the VFD that i should check? Thanks in advance Edit 1.

Yes it looks like the freq. On the parameter 4 its on 50 HZ, but it cannot be changed to a higher one. Now taking a better inspection Pd003 (according the manual MAIN FREQUENCY) remains on 50Hz, cannot be changed to a higher freq im assuming that this is the input frequency., Pd004 now i set it on 60Hz but i read somewhere that is better to put a higher value (400 was the recommended frequency). Is this safe for the VFD?

Now Pd005 must be 60Hz or should i also changed it to 400 Hz? I have just setup a DigiSpeed alongside a 1.5Kw Huanyang Inverter. All the settings and configurations I have followed as per the information I have read on this forum. I have my terminals 3 terminals setup as VR(+10V), VI (0-10V input), and ACM (analog common ground). When I turn on the spindle with Mach3 I get corresponding voltage between VI and ACM which changes with selected speed all the way up to 9.8volts at full. I have set PD070 at 0 and tried 4 I have set PD001 and PD002 to external settings.

The spindle runs fine once I set it to operator but will not move or do anything if I try to command it from Mach3 Any ideas? I have spent some time on this without success!!! Regards Boyd NZ.

Add new comment.